Tweet
I like the merc with a park bench on the back.......
-
-
My Evo 2 version is better than those above . Plus i'll kick their arses in a race , the 205T16 will need 600bhp too keep up .
sigpic 2.1 ATMO YB POWER .
Tick tock goes the clock and the clock don't lie .
12.4sec to 109mph With NO turbo , NO gay trailer , NO slicks , NO gas , NO race fuel and NO bits missing . Beat that !!!!Comment
-
as Andy Green, Richard Noble and the rest of the SSC team celebrated, news of mk1gaz's new record run filtered through with his 'comfy' LSR car
Comment
-
the most important thing to remember after youve done this gaz is to change your statement at the bottom of your posts
dont get tooo bufty you wont want to drive it
sigpicComment
-
I'm not going mad with the bufty bit . 1x can of satin black for the x-member and steering rack and that's about it . It's quite bufty looking normally except for all the dead flies splattered all over it .
sigpic 2.1 ATMO YB POWER .
Tick tock goes the clock and the clock don't lie .
12.4sec to 109mph With NO turbo , NO gay trailer , NO slicks , NO gas , NO race fuel and NO bits missing . Beat that !!!!Comment
-
Imagine the size of their trailer !!!Originally posted by grum View Postas Andy Green, Richard Noble and the rest of the SSC team celebrated, news of mk1gaz's new record run filtered through with his 'comfy' LSR car
sigpic 2.1 ATMO YB POWER .
Tick tock goes the clock and the clock don't lie .
12.4sec to 109mph With NO turbo , NO gay trailer , NO slicks , NO gas , NO race fuel and NO bits missing . Beat that !!!!Comment
-
Can just see a slick poking out aswell
Part of the Java Green clubComment
-
and it was a genuine "steer from the rear"Originally posted by GraemeJ View PostCan just see a slick poking out aswell
Comment
-
Just been down the garage to fit the new steering bits and :
New 2.5 quick rack = check
New GP4 steering joint = check
2x New rs2000 mk2 track rod ends to fit rack = check
2x New alloy steering rack mounts = check
2x Locknuts for the trackrod ends onto new steering rack = Doh , bollox , foooooooooooooook !!!
Bloody typical , so i still can't fit it .
sigpic 2.1 ATMO YB POWER .
Tick tock goes the clock and the clock don't lie .
12.4sec to 109mph With NO turbo , NO gay trailer , NO slicks , NO gas , NO race fuel and NO bits missing . Beat that !!!!Comment
-
I bet we all have been in the same situation,frustrating isnt it.Comment
-
Sure is mate , sourcing all the little bits and bobs takes the most time up for sure .
Anyway the racks in now so i just need to fit the trackrod ends later on . Engine's in (bottom end) as well and dry sump pump and oil lines etc .
I couldn't push the car out the garage so had to lift the engine in by hand as the hoist hits the garage roof .
Me and a mate just lifted it straight in without a rope or pole etc . We covered the slam panel with a blanket and lifted the engine onto that , then in one swoop dropped it into the x-member . Very easy and much quicker than any other method , proper old skool .
sigpic 2.1 ATMO YB POWER .
Tick tock goes the clock and the clock don't lie .
12.4sec to 109mph With NO turbo , NO gay trailer , NO slicks , NO gas , NO race fuel and NO bits missing . Beat that !!!!Comment
-
We all like pics so here's a couple .
sigpic 2.1 ATMO YB POWER .
Tick tock goes the clock and the clock don't lie .
12.4sec to 109mph With NO turbo , NO gay trailer , NO slicks , NO gas , NO race fuel and NO bits missing . Beat that !!!!Comment
-
5 minutes ?Comment
-
Less mate , took about 5 seconds !!!Originally posted by essy View Post
sigpic 2.1 ATMO YB POWER .
Tick tock goes the clock and the clock don't lie .
12.4sec to 109mph With NO turbo , NO gay trailer , NO slicks , NO gas , NO race fuel and NO bits missing . Beat that !!!!Comment
-
What are you like! engine bay looks as clean as ever.Comment
Comment