Announcement

Collapse
No announcement yet.

And again LOL

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Spent all sodding day fitting this tw4t of a thing. If anyone is thinking of getting one......forget it LOL So tight to everything. Glad it's on though and am NEVER going to take it off again PMSL




    Autumn Has Arrived by Kevin Frost, on Flickr

    CHES'S UNDERSTUDY...........

    Comment


    • good job james must of been that calming person after school

      its on

      heated brake fluid could be a concern tho
      MK2 member 091, RSOC member 2675, RS18 No 001, HRE7724 /50

      My Car in the VbGarage and in My Album

      Comment


      • Should have got one that fits right.....:winka: wot a ****


        I'd rather push a Ford than drive a V**X***L

        Comment


        • Originally posted by Dave1800BDA View Post
          good job james must of been that calming person after school

          its on

          heated brake fluid could be a concern tho
          Oh she didn't calm me LOL

          Yeah, Heated fluid, Heated clutch cable, Heated paint is all a worry I think some heat shielding will be needed.
          Autumn Has Arrived by Kevin Frost, on Flickr

          CHES'S UNDERSTUDY...........

          Comment


          • Originally posted by RS2K View Post
            Should have got one that fits right.....:winka: wot a ****
            Shut it Idiot chops. You are going to get PAIN tonight mush :winka:
            Autumn Has Arrived by Kevin Frost, on Flickr

            CHES'S UNDERSTUDY...........

            Comment


            • Originally posted by Frosticles View Post
              Oh she didn't calm me LOL
              pmsl got you going then
              MK2 member 091, RSOC member 2675, RS18 No 001, HRE7724 /50

              My Car in the VbGarage and in My Album

              Comment


              • looking good kev.
                Are you still going to run the servo and tower? if yes you will need to cut a section out of the tower to fit past the exhaust, I also had to grind back the pushrod linkage in the tower as it touched my exhaust.
                You will need to wrap the clutch cable and route in a way to clear now and yes you will need heat protection on your brake pipes and floor pan now

                my_car_in_the_vBGarage

                Comment


                • Originally posted by Dave1800BDA View Post
                  pmsl got you going then
                  Just a little PMSL. Just one of those women that Rings my bell so to speak.
                  Originally posted by hotrs2000 View Post
                  looking good kev.
                  Are you still going to run the servo and tower? if yes you will need to cut a section out of the tower to fit past the exhaust, I also had to grind back the pushrod linkage in the tower as it touched my exhaust.
                  You will need to wrap the clutch cable and route in a way to clear now and yes you will need heat protection on your brake pipes and floor pan now
                  Am going to see what the tower does as I would like to keep it. Glad I didn't fit the manifold whilst it was in place..... Daft question but where can I get heat shielding from?
                  Autumn Has Arrived by Kevin Frost, on Flickr

                  CHES'S UNDERSTUDY...........

                  Comment


                  • Originally posted by Frosticles View Post


                    you should have left it there!!

                    Comment


                    • Originally posted by Frosticles View Post
                      Shut it Idiot chops. You are going to get PAIN tonight mush :winka:
                      What you worried about Kev it will not be running long enuogh to get hot on the trailer off the trailer
                      Difficult roads often lead to beautiful places

                      Comment


                      • demon thieves or rally re-design sell the heat wrap stuff kev.you can get small bore heat sleeves that will go over the clutch cable and brake pipes and it looks very tidy from them both.sure d/t show it on there online shop shite.looking nice tho m8y well done
                        sigpic

                        Comment


                        • Originally posted by Frosticles View Post
                          Am going to see what the tower does as I would like to keep it. Glad I didn't fit the manifold whilst it was in place..... Daft question but where can I get heat shielding from?
                          just google it mate loads of places sell it, Burtons, demon tweeks etc etc have a look at some of kit car and restoration companies as sometimes they are cheaper than the motor-sport shops

                          my_car_in_the_vBGarage

                          Comment


                          • Thas coming on very nicely, very impressive, all the blood ,sweat and tears will be worth it when its done and be good to see it in the flesh
                            sigpic

                            Comment


                            • Originally posted by Dave1800BDA View Post
                              heated brake fluid could be a concern tho
                              yes watch out for that kev, you will get brake fade whilst out on track and before you know it you will be in the gravel.....................AGAIN



                              cheeRS
                              sigpic

                              Comment


                              • Originally posted by graham John View Post
                                yes watch out for that kev, you will get brake fade whilst out on track and before you know it you will be in the gravel.....................AGAIN



                                cheeRS
                                Pembery doesn't have gravel


                                Many thanks for all your replies
                                Autumn Has Arrived by Kevin Frost, on Flickr

                                CHES'S UNDERSTUDY...........

                                Comment

                                Working...
                                X